|
Physical Properties | Original Value | Comments |
---|
Density | 1.14 - 1.82 g/cc |
| 1.12 - 1.35 g/cc @Temperature 260 - 295 °C |
Filler Content | 25.0 - 35.0 % |
Water Absorption | 0.200 - 8.00 % |
Moisture Absorption at Equilibrium | 0.170 - 5.70 % |
| 1.20 - 2.20 % @Temperature 70.0 - 70.0 °C |
Water Absorption at Saturation | 0.800 - 9.00 % |
Additive Loading | 25.0 - 33.0 % |
Viscosity | 2.90 - 50.0 cP |
| 20.0 - 190000 cP @Temperature 100 - 2000 °C |
| 20.0 - 190000 cP @Shear Rate 10.0 - 10000 1/s |
Viscosity Test | 150 cm³/g |
Viscosity Number | 124 - 215 cm³/g |
Maximum Moisture Content | 0.0200 - 0.200 |
| 0.200 - 0.200 @Temperature 120 - 120 °C |
| 0.200 - 0.200 @Time 299 - 299 sec |
Linear Mold Shrinkage | 0.000350 - 0.0550 cm/cm |
| 0.00200 - 0.00600 cm/cm @Temperature 80.0 - 80.0 °C |
Linear Mold Shrinkage, Transverse | 0.00100 - 0.0980 cm/cm |
| 0.00800 - 0.0100 cm/cm @Temperature 80.0 - 80.0 °C |
Melt Flow | 1.00 - 198 g/10 min |
Spiral Flow | 35.0 - 757 cm |
Ash | 23.0 - 36.0 % |
| 28.0 - 32.0 % @Temperature 625 - 625 °C |
|
Mechanical Properties | Original Value | Comments |
---|
Hardness, Rockwell L | 110 |
Hardness, Rockwell M | 58.0 - 120 |
Hardness, Rockwell R | 85.0 - 125 |
| 24.0 - 24.0 @Temperature 80.0 - 80.0 °C |
Hardness, Shore D | 77.0 - 90.0 |
Ball Indentation Hardness | 90.0 - 280 MPa |
Tensile Strength, Ultimate | 19.0 - 248 MPa |
| 35.0 - 235 MPa @Temperature -40.0 - 150 °C |
Tensile Strength, Yield | 18.8 - 290 MPa |
| 231 - 240 MPa @Temperature -40.0 - -40.0 °C |
Elongation at Break | 1.00 - 190 % |
| 2.00 - 6.80 % @Temperature -40.0 - 150 °C |
Elongation at Yield | 2.00 - 11.0 % |
| 3.50 - 6.00 % @Temperature 60.0 - 150 °C |
Modulus of Elasticity | 0.0848 - 19.7 GPa |
| 0.220 - 9.30792 GPa @Temperature -40.0 - 150 °C |
Flexural Yield Strength | 26.2 - 331 MPa |
| 100 - 325 MPa @Temperature -40.0 - 121 °C |
Flexural Modulus | 0.758 - 98.1 GPa |
| 3.10 - 11.6 GPa @Temperature -40.0 - 121 °C |
Flexural Strain at Break | 2.50 - 7.00 % |
Compressive Yield Strength | 28.0 - 240 MPa |
| 70.0 - 250 MPa @Temperature -40.0 - 80.0 °C |
Poissons Ratio | 0.340 - 0.400 |
Shear Modulus | 0.0900 - 3.90 GPa |
Shear Strength | 50.0 - 95.0 MPa |
Izod Impact, Notched | 0.450 - 75.0 J/cm |
| 0.500 - 3.84408 J/cm @Temperature -40.0 - 149 °C |
| 0.64068 - 2.24238 J/cm @Temperature -40.0 - 72.8 °C |
| 0.64068 - 2.24238 J/cm @Thickness 3.17 - 3.17 mm |
Izod Impact, Unnotched | 0.0816 J/cm - NB |
| 0.900 - 7.00 J/cm @Temperature -30.0 - -30.0 °C |
Izod Impact, Notched (ISO) | 2.50 - 95.0 kJ/m² |
| 4.00 - 70.0 kJ/m² @Temperature -40.0 - -30.0 °C |
Izod Impact, Unnotched (ISO) | 6.50 - 21000 kJ/m² |
| 6.00 - 95.0 kJ/m² @Temperature -40.0 - -30.0 °C |
Charpy Impact Unnotched | 0.600 J/cm² - NB |
| 0.600 J/cm² - NB @Temperature -40.0 - -20.0 °C |
| 4.20 - 7.00 J/cm² @Temperature 120 - 135 °C |
| 4.20 - 7.00 J/cm² @Time 720000 - 720000 sec |
Charpy Impact, Notched | 0.250 - 12.0 J/cm² |
| 0.294 - 8.50 J/cm² @Temperature -40.0 - -20.0 °C |
Puncture Energy | 2.10 - 5.40 J |
| 1.90 - 2.50 J @Temperature -30.0 - -30.0 °C |
Coefficient of Friction | 0.150 - 0.610 |
Coefficient of Friction, Static | 0.140 - 0.410 |
Tensile Creep Modulus, 1 hour | 5000 - 9350 MPa |
Tensile Creep Modulus, 1000 hours | 2000 - 5620 MPa |
K (wear) Factor | 26.2 - 604 x 10-8 mm³/N-M |
Limiting Pressure Velocity | 0.120 - 0.701 MPa-m/sec |
Taber Abrasion, mg/1000 Cycles | 0.400 - 26.0 |
|
Electrical Properties | Original Value | Comments |
---|
Electrical Resistivity | 1000 - 1.00e+18 ohm-cm |
Surface Resistance | 50.0 - 3.00e+16 ohm |
Static Decay | 2.00 sec |
Dielectric Constant | 2.70 - 12.0 |
Dielectric Strength | 1.97 - 90.0 kV/mm |
Dissipation Factor | 0.00160 - 0.460 |
Dielectric Loss Index | 0.0140 - 0.150 |
Arc Resistance | 0.000 - 180 sec |
Comparative Tracking Index | 0.000 - 600 V |
Hot Wire Ignition, HWI | 0.000 - 300 sec |
High Amp Arc Ignition, HAI | 0.000 - 187 arcs |
High Voltage Arc-Tracking Rate, HVTR | 10.0 - 150 mm/min |
|
Thermal Properties | Original Value | Comments |
---|
CTE, linear | 3.24 - 90.0 µm/m-°C |
| 9.00 - 21.0 µm/m-°C @Temperature 55.0 - 160 °C |
| 16.0 - 26.0 µm/m-°C @Temperature 35.0 - 55.0 °C |
| 16.0 - 26.0 µm/m-°C @Thickness 2.00 - 2.00 mm |
CTE, linear, Transverse to Flow | 2.70 - 120 µm/m-°C |
| 110 - 146 µm/m-°C @Temperature 55.0 - 160 °C |
Specific Heat Capacity | 0.340 - 2.35 J/g-°C |
| 1.91 - 2.29 J/g-°C @Temperature 260 - 295 °C |
Thermal Conductivity | 0.216 - 1.60 W/m-K |
| 0.210 - 0.250 W/m-K @Temperature 260 - 295 °C |
Melting Point | 160 - 325 °C |
Maximum Service Temperature, Air | 65.0 - 288 °C |
Hot Ball Pressure Test | 205 - 220 °C |
Deflection Temperature at 0.46 MPa (66 psi) | 120 - 297 °C |
Deflection Temperature at 1.8 MPa (264 psi) | 76.0 - 285 °C |
Deflection Temperature at 8.0 MPa | 65.6 - 220 °C |
Vicat Softening Point | 195 - 258 °C |
Minimum Service Temperature, Air | -30.0 - 130 °C |
Glass Transition Temp, Tg | 5.00 - 80.0 °C |
Decomposition Temperature | 310 °C |
UL RTI, Electrical | 65.0 - 160 °C |
UL RTI, Mechanical with Impact | 65.0 - 160 °C |
UL RTI, Mechanical without Impact | 65.0 - 140 °C |
Flammability, UL94 | HB - 5VA |
Flame Spread | 0.000 - 80.0 mm/min |
Oxygen Index | 22.0 - 38.0 % |
Glow Wire Test | 600 - 975 °C |
Ignition Temperature | 350 - 400 °C |
|
Processing Properties | Original Value | Comments |
---|
Processing Temperature | 70.0 - 310 °C |
Nozzle Temperature | 80.0 - 340 °C |
Die Temperature | 255 - 315 °C |
Melt Temperature | 210 - 340 °C |
Mold Temperature | 26.7 - 160 °C |
Drying Temperature | 65.6 - 130 °C |
Moisture Content | 0.0200 - 0.200 % |
Dew Point | -17.8 °C |
Injection Pressure | 3.45 - 138 MPa |
Vent Depth | 0.00127 - 0.00762 cm |
Some of the values displayed above may have been converted from their original units and/or rounded in order to
display the information in a consistent format. Users requiring more precise data for scientific or engineering
calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding
error. We also ask that you refer to MatWeb's
terms of use regarding this information.
Click here to go back to viewing the property data in MatWeb's normal format.